Newsletter

 

For a Free Quote...

Candela - LANforge Fire Stateful Network Traffic Generator

LANforge-FIRE Stateful Network Traffic Generator 

  Candela-Network Traffic Generator
Candela-Lanforge-Traffic-Generator

 


 

LANforge FIRE

 generates and receives various network protocols. It is used to create load on a network under test. It reports statistics such as packets sent and received, latency, packet-loss and many other network characteristics. LANforge supports real protocols and stateful TCP connections, so it can generate load against web servers, VOIP gateways, firewalls, load-balancers and many other network components. LANforge can virtualize network adapters and wifi station interfaces. It can also act as a router or group

 of routers supporting OSPF, RIP, BGP and Multicast (PIM, IGMP). LANforge supports IPv4 and IPv6. The LANforge system consists of a single manager process, and one or more traffic generator machines (resources). The resources are connected to the manager over a management network. Devices under test are connected to the non-management ports of LANforge systems. If needed, LANforge can also generate traffic on the management network. The LANforge GUI may run on the LANforge machines or on the customer's PCs. The GUI should connect to the manager machine. Multiple GUIs can be used concurrently. - test

LANforge FIRE Use Cases 

  • Validate network equipment for throughput, stability and performance, at up to 10Gbps speeds. All supported protocols can be used concurrently for a very realistic traffic mix.
  • 24 and 48-port modules especially cost-effective for testing many slower systems, such as DSL, Cable-Modem, and Satellite modems.
  • WiFIRE models can emulate up to 128 WiFi clients per chassis for testing access points and other wireless infrastructure.
  • VOIP Call generation can be used to load SIP gateways and other VOIP infrastructure. It can report various statistics, including PESQ quality scores.
  • HTTP, HTTPS, FTP and similar load generation can be used to test web servers, load balancers, and related equipment.
  • LANforge can support 30,000+ concurrent stateful TCP connections, so it can be used to test firewalls, routers, and other equipment that pays close attention to higher level protocols.

LANforge FIRE Protocols & Connections

  1. Supports real-world protocols: (Benchmarked on high-end Candela Technologies-supplied hardware)
    1. Layer 2: Raw-Ethernet
    2. PPP: Supports PPPoE interfaces
    3. Layer 3: Armageddon accellerated UDP/IP (9.99 Gbps+ with 1514 byte frames on 10 GE; 990 Mbps, 81,800 pps on GigE; both symmetrical and bidirectional, sending to self (2 ports)) *
    4. Layer 3: UDP/IP (6 Gbps+ bi-directional, 3 streams, 24k byte PDUs, 1500 MTU, 10G, to self, some drops)
    5. Layer 3: UDP/IPv6 (6 Gbps+ bi-directional, 3 streams, 24k byte PDUs, 1500 MTU, 10G, to self, some drops)
    6. Layer 3: IGMP Multicast UDP (500+ receivers)
    7. Layer 3: IGMP Multicast UDP over IPv6 (500+ receivers)
    8. Layer 3: Stateful TCP/IP (9.8Gbps+ on wire, 9.3Gbps goodput, bi-directional with 24K byte writes, 30 streams, 1500 MTU, 10G, to self)
    9. Layer 3: Stateful TCP/IPv6 (9.8Gbps+ on wire, 9.1Gbps goodput, bi-directional with 24K byte writes, 30 streams, 1500 MTU, 10G, to self)
    10. Layer 3: Stateful SCTP/IP (850Mbps, bi-directional, 3 streams. No hardware offload exists, CPU bound.)
    11. Layer 3: Stateful SCTP/IPv6 (850Mbps, bi-directional, 3 streams. No hardware offload exists, CPU bound. Requires global-scope IPv6 addresses.
    12. Layer 4: FTP
    13. Layer 4: SFTP
    14. Layer 4: HTTP (9 Gbps+ download, 65,000+/13,000+ Requests per Second, 6,000+ concurrent connections)
    15. Layer 4: HTTPS (1 Gbps+ download)
    16. Layer 4: SCP
    17. Layer 4: TFTP (1400+ concurrent connections, ~1Gbps throughput)
    18. Layer 4: TELNET
    19. Layer 4: DNS (Used and Reported by most Layer 4 traffic types)
    20. Layer 4: PING (via integrated script)
    21. Layer 4: VoIP Call Generator (SIP, RTP, RTCP, PESQ/MOS), 1000+ calls per machine. *
    22. File-IO: NFS 17+Gbps (dual 10G NICs, mostly reading), 1000+ virtual clients.
  2. Supports over 50,000 concurrent TCP connections on a single high-end machine with appropriate licenses. Base license includes 1000 concurrent connections. Supports around 2000 concurrent Layer 4, UDP and other connection types. *
  3. Supports real-world compliance with ARP protocol.
  4. Supports ToS (QoS) settings for TCP/IP and UDP/IP connections.
  5. Utilizes libcurl for FTP, SFTP, TFTP, SCP, TELNET, HTTP and HTTPS (SSL) protocols.
  6. Supports file system test endpoints (can be used for NFS, NFSv4, SMB, and iSCSI file systems too!). Can emulate 1000+ CIFS and/or NFS clients with unique mount points, IPs, MACs, etc *
  7.  Supports custom and command-line programs, like nmap and ping.
  8. Custom packet builder interface allows hand crafting of headers and payloads. Headers supported at Layer 2 include ARP, SNAP/LLC, 802.1Q, 802.1QinQ and MPLS. Some Layer 3 protocol headers supported include IP, IPX, UDP, TCP, ICMP, IGMP, IP-ENCAP, RDP, IPinIP and IPv6 protocols.
  9. Uses publicly available Linux or Windows networking stack for increased standards compliance.
  10. Supports 20 or more physical data-generating Ethernet ports per 2U LANforge chassis.
  11. Emulates over 2000 unique machines with one physical interface with the MAC-VLAN feature! *
  12. Supports over 2000 802.1Q VLANs .*
  13. Supports PPPoE, including automated creation and deletion of the PPP interfaces
  14. Supports 802.11a/b/g/n/AC with WiFIRE feature set (see below.)

LANforge FIRE Reporting

  • Comprehensive traffic reports include: Packet Transmit rate, Packet Receive rate, Packet Receive Drop %, Transmit Bytes, Receive Bytes, Latency, various Ethernet driver level counters, and much more.
  • Supports generation of reports that are ready to be imported into your favorite spread-sheet.
  • Allows packet sniffing and network protocol decoding with the integrated Wireshark protocol sniffer.

Management & Platform Support

  • Comprehensive management information detailing all aspects of the LANforge system including machine statistics, test cases, and Ethernet port statistics.
  • The LANforge Management GUI manages the LANforge systems and may be run locally on the LANforge system or over the network.
  • The GUI can manage multiple units, tests, and testers simultaneously.
  • The GUI is supported on Linux, Windows, Solaris, and other operating systems.
  • Supports scriptable command line interface (telnet) which can be used to automate test scenarios. Perl libraries and example scripts are also provided!
  • LANforge testing software supported on Linux, Microsoft Windows and Solaris.
  • Automatic discovery of LANforge systems simplifies maintenance of LANforge test equipment.
  • The modular architecture that allows you to leverage your existing LANforge investment as your need for capacity increases.
  • LANforge FIRE feature set may be combined with LANforge ICE to provide background traffic for more realistic testing.

LANforge VoIP/RTP Call Generator Feature Highlights

SIP protocol used for call management.
  • SIP/UDP supported.
  • Can use directed mode, where VoIP phones call directly to themselves.
  • Can also use Gateway mode where the VoIP phones register with a SIP or H.323 gateway.
  • SIP authentication is supported.
RTP protocol used for streaming media transport, and supports the following CODECS. More codecs may be supported in the future.
  • G.711u: 64kbps data stream, 50 packets per second (SIP, H.323)
  • G.729a: 8kbps data stream, 50 packets per second (SIP ONLY)
  • Speex: 16kbps data stream, 50 packets per second (SIP on Linux ONLY)
  • G.726-16: 16kbps data stream, 50 packets per second (SIP ONLY)
  • G.726-24: 24kbps data stream, 50 packets per second (SIP ONLY)
  • G.726-32: 32kbps data stream, 50 packets per second (SIP ONLY)
  • G.726-40: 40kbps data stream, 50 packets per second (SIP ONLY)
  • NONE: A messaging-only configuration is now supported (SIP ONLY)
  • Supports PESQ automated voice quality testing.
  • RTCP protocol used for streaming media statistics (SIP only)
  • Each LANforge VoIP/RTP endpoint can play from a wav file and record to a separate wav file. Almost any sound file can be converted to the correct wav file format with tools bundled with LANforge. Sample voice files are included.
  • Support for 1000 or more emulated VoIP phones per machine (hardware dependent)
  • LANforge VoIP/RTP endpoints can call other LANforge endpoints or third party SIP phones like Cisco and Grandstream. Third party phones can also call LANforge endpoints and hear the WAV file being played

LANforge WiFIRE 802.11b Traffic Generator

  1. Useful for testing Wireless Access Points and deployments. Candela LANforge-WiFIRE
  2. Can emulate up to 128 802.11a/b/g/n wireless client stations (Virtual STAs) per radio.
  3. Each radio can run on only a single frequency at a time. So, all stations must be able to connect to an AP on the same channel.
  4. Each Virtual STA can be associated with a particular Access Point (AP).
  5. Each Virtual STA can be set to a specific protocol (/a, /b, /g /n) or be told to use the best option available.
  6. For 802.11n, HT-40 can be disabled.
  7. For all protocols, the rates can be specified or left auto. 
  8. AMPDU density and factor can be modified for 802.11n stations. 
  9. Each Virtual STA has unique MAC address, IP address and routing table.
  10. 128bit WEP, WPA2 and related wpa_supplicant authentication methods supported.
  11. Advanced authentication support includes: 802.1x, 802.11u, HotSpot 2.0/HS2.0, EAP-TLS, EAP-TTLS with MSCHAPv2, EAP-SIM, EAP-AKA, etc.
  12. Automated captive portal login support for Virtual STAs.
  13. Supported standards include: 802.11r (OTA and over DS), 802.11w.
  14. Supports all LANforge FIRE stateful traffic generation features, including HTTP, TCP, UDP, TCPv6, UDPv6, VOIP (SIP, RTP) * and more.
  15. Supports bridge mode where wired Ethernet traffic can connect to the wired port on the LANforge an have their traffic sent onto the wireless network. This allows third-party traffic generators to be used. Each MAC address is associated with a single WiFi station in LANforge. With release 5.2.2, traffic can be bridged by IP address as well. 

LANforge NetReplay & Backtrack Feature Highlights

  1. Using a combination of the LANforge FIRE traffic generation and LANforge ICE network emulation, LANforge supports capture and replay of Ethernet packet streams.
  2. Capture protocol can be converted to standard 'libpcap' format for use with other tools such as Wireshark and tcpdump.
  3. Capture has been benchmarked at 1Gbps bi-directional on high-end hardware using 6TB RAID configuration.

Virtual Network Builder

LANforge Netsmith is a drag-and-drop virtual network builder. It can support virtual routers, emulated network links, bridges (switches), virtual and physical interfaces, and more. When using routers, it supports static, OSPF, BGP, Multicast (IGMP, PIM) and other protocols for IPv4 and IPv6. LANforge FIRE stateful traffic generating connections and LANforge ICE network emulations are easily placed in the virtual networks. The virtual routers can connect to external routers and other network elements for easy integration into your network.

  • Emulates networks of arbitrary complexity using real-world routing protocols by integrating with the XORP router daemon.
  • Supports IPv4 and IPv6 static routing.
  • Supports IPv4 and IPv6 OSPF routing.
  • Supports IPv4 and IPv6 multicast routing.
  • Supports basic RIP, OLSR, and BGP routing protocol features.
  • Supports Ethernet bridges (switches), including spanning tree protocol (STP).
  • The virtual interfaces are 'real', so you can configure them like normal network interfaces and use sniffers and other tools on the individual interfaces.
  • Virtual router interconnections can be associated with LANforge ICE network emulations.
  • Interfaces can be associated with LANforge FIRE stateful traffic generation connections.
  • See the LANforge FIRE and LANforge ICE and cookbook for examples of how Netsmith works.

LANforge FIRE Systems

LANforge FIRE is often customized to a customer's specifications. In particular all of the LANforge ICE Network Emulation feature set is available. Some standard systems are listed below, but please contact your sales representative to discuss your requirements in detail and for a customized quote.

LANforge-FIRE Related Screen Shots

Layer 3 (Ethernet, UDP, TCP) Connections

Layer 3 (Ethernet, UDP, TCP) Connections

Layer 3 Create/Modify Screen

Candela

LANforge on Microsoft Windows

LANforge supports Microsoft Windows operating systems, but Linux is still the preferred platform for advanced features and higher stability, performance and precision.

Some features currently supported on Windows:

  1. Layer 2: Raw-Ethernet
  2. Layer 3: IPv4: UDP, TCP, Custom UDP, Custom TCP
  3. Layer 3: IPv6: UDP, TCP (XP only, not available on Vista currently)
  4. Layer 4+: HTTP, HTTPS (SSL), FTP, VoIP (SIP, RTP), File-IO (CIFS, etc.)
  5. Display of interface (adapter) related statistics and settings
  6. Custom packet builder interface allows hand crafting of headers and payloads. Headers supported at Layer 2 include ARP, SNAP/LLC, 802.1Q, 802.1QinQ and MPLS. Some Layer 3 protocol headers supported include IP, IPX, UDP, TCP, ICMP, IGMP, IP-ENCAP, RDP and IPinIP.

 For detailed information on specific features, please contact your sales representative.

Some features currently NOT supported on Windows:

  1. Layer 3: IPv6 on Vista (Supported on XP)
  2. Armageddon UDP packet generator
  3. PPPoE, PPP/T1
  4. LANforge WiFIRE 802.11a/b/g/n client emulation.
  5. Virtual interfaces (802.1Q, MAC-VLANs)
  6. Virtual routers.
  7. Configuration of interfaces (adapters) through LANforge. You can configure the interfaces through the normal Windows tools instead.

For detailed information on specific features, please contact your sales representative.

 

Contact Us

Address:

Telnet Networks Inc.
1324 Andersen Drive
Kingston, ON  K7P 0C6
Canada

Phone:

(800) 561-4019

Fax:

613-498-0075

For More Information about Telnet Networks, our products, or our services, or to request a quote please feel free to contact us directly.

Latest Blog Posts

Latest Blog Posts